Thursday, November 27, 2008

Introduction to Head Units

Ideally, your caput unit of measurement would be used to supply a signaling to your amplifiers that is line degree and you would not utilize its internal amplifiers (if any). They usually make not have got the powerfulness and strength to drive talkers both loudly and cleanly. The line degree signaling is cleaner than the talker degree end products on the caput unit of measurement of measurement because it is makes not travel through the internal amplifiers in the caput unit. That beingness said there are occasions where you would utilize the caput unit's internal power. One state of affairs is when you are on a budget and are building your system over time. The caput unit of measurement can be used to drive talkers (but not subwoofers) until you can acquire an amp. The other state of affairs is when you are building a system where the benefits of an ampere are not of import to you. Read my planning page for more than than than inside information about what is right for you.

No caput unit of measurement of measurement typically have more than about 60watts of entire end product powerfulness because more would necessitate a existent DC-DC powerfulness supply (which makes not suit in a caput unit easily). Using the caput unit of measurement of measurement powerfulness can be a impermanent solution until a separate amplifier can be purchased, just make certain you do not seek to powerfulness any subwoofers or insensitive constituent sets with the caput unit's built in power. According to Car Audio and Electronics magazine, most caput units of measurement utilize the same bits for the internal amplifiers so they all green goods about the same low power. The best they have got measured is about 14watts into 4 channels at 1% distortion. Their powerfulness degree at a better take down deformation figure (like 0.1%) is significantly lower.

Note about using mill caput units: Many people inquire me about using the mill caput unit of measurement that came with their auto with external aftermarket amps. Typically you cannot acquire a clean signaling from the caput unit of measurement because mill caputs make not have got line degree (RCA) pre-amp end products to drive an amp. You can utilize a talker degree to line degree convertor but the sound is still going through the mill head's internal amps. Some people are willing to give some sound quality in order to maintain their mill head. Also, if your mill system utilizes an external ampere you may be able to happen an arranger so you can utilize an aftermarket ampere instead.

Things to look for:

Usability: Your caput unit of measurement is the portion of the auto stereo system that you interact with most so it is of import to acquire one that "feels" good to you. Always expression at a caput unit of measurement in a shop show and usage it for awhile. Try to toss through radiocommunication stations and paths on a cadmium to see if it is speedy and easy. If you have got jobs with little buttons, conceive of what it will be like when you are driving! Since many theoretical accounts in the same terms scope are similar in characteristics and sound quality, usability is often the crucial factor between models.

Power: Even though I just said not to utilize the built-in power-assisted of a caput unit of measurement I cognize sometimes it is necessary. Bear in caput that the powerfulness specs given by most makers for head units of measurement are not accurate. They often utilize footing like "music power" or "peak power" which have got small existent significance because there is no criterion definition of those terms. If the powerfulness is quoted in "RMS" footing then it is usually accurate. However, there is still one other topographic point of misconception. Often makers will cite powerfulness as "30watts x 4 RMS". The "RMS" looks to intend it is a true indicant of powerfulness but they are implying that all 4 channels can bring forth 30watts rms astatine THE SAME TIME. With a caput unit, this is almost always not true. Because of the little powerfulness stores in caput units of measurement they can rarely end product more than 15-60 Watts TOTAL. This agency that the powerfulness to each transmission channel at upper limit burden would only be 1/4 of that total. Some makers are better than others about giving accurate specs and a few theoretical accounts are available with sophisticated powerfulness stores which have got higher powerfulness end product but they are VERY expensive. If you're paying less than $800 for a caput unit of measurement (and most of us are!) then your caput unit of measurement will not set out much power. I have got written a more than comprehensive account of powerfulness amplifier spectacles as well. Speakers which are not producing bass make not pull nearly as much powerfulness so you can acquire away with using the caput unit of measurement to powerfulness them but usage passive voice high base on balls crossings over (bass blockers) and they will play even louder and cleaner. Bear in caput that the deformation may be higher from the head unit of measurement than an external ampere however.

Cassette vs. CD: This pick is mostly a substance of preference. If you make not have got many cassettes then an in-dash cadmium participant is probably correct for you. If you necessitate the capableness to listen to cassettes and CDs then a cassette caput unit of measurement with modifier controls should be adequate. Be aware that many in-dash cadmium caput units of measurement can command a cadmium modifier as well so you can utilize both. An in-dash cadmium is convenient for changing phonograph records quickly while on the road. Because of size of most cadmium modifiers they are usually mounted in the tree trunk or under the seating although there are some newer theoretical accounts which are little adequate to suit in baseball glove compartments. Under the seating or in the tree trunk are not easy topographic points to acquire to while you're driving!

Theft Protection: Detachable confronts are the most common larceny bar strategy in caput units of measurement today. There are two flavors, fully detachable and partially detachable. With a fully detachable human human human face all the controls on the presence come up off leaving behind a clean panel, whereas a partially detachable face go forths some characteristics on the caput unit of measurement of measurement but the caput unit is still useless without the face. Fully detachable human faces are bigger and bulkier to transport around than partially detachable 1s but go forth nil behind to be seen. Another option is Eclipse's ESN system. With these caput units of measurement when you first use powerfulness to them you must provide a cadmium which the unit of measurement retrieves as the "reference" CD. Thereafter if the unit of measurement ever loses powerfulness you must infix the "reference" cadmium before it will work again. Only you cognize what the "reference CD" is so the caput unit of measurement is useless to a thief. Eclipse also tracks the units of measurement they repair. More than once a purloined caput unit of measurement was returned to them for service because it was not working. Upon verifying the caput unit of measurement of measurement was purloined they can apprehend the stealer as the individual who returned the stolen caput unit for service. I still wouldn't number on the stealer to cognize that Eclipse makes this though so I lodge with a conventional fully detachable face. A new turn from Kenwood tosses the human face around when you turn off the powerfulness so the stealer can't see the caput unit. I believe it would work even better if the human human human face then went back into the caput unit, giving the visual aspect that the unit of measurement of measurement of measurement of measurement is a detachable face caput unit with its face removed.

Pre-amp outputs: These are must for any serious caput unit. These end products let you to run an amplifier directly without demand for any conversion. This is the cleanest end product of the caput unit. Some units of measurement have got multiple end products and sometimes 1s that are crossed over. Look for the amount and type that you necessitate for your system but maintain in head hereafter expansion. One is sufficient but having two let you fade, or set the degrees of multiple amplifiers right from the caput unit. Some caput units of measurement now offer 4 V end products instead of the usual 1-2 volts. This tin be very good since autos have got a batch of electrical noise in them. The 4 V end product is less susceptible to noise, however, you must be certain that the amplifier or crossing over being connected to the end product can manage 4 VS or you will not be able to utilize the other voltage. If your caput unit of measurement makes not have got pre-amp flat (RCA type) end products you can purchase an arranger which will convert your talker degree end products to line level. They run in terms from $12 on up but since I have got not used them I make not cognize how much difference there is among them. Another option is to utilize an amplifier that accepts talker degree signalings directly but those are not as easy to find.

Other features: There are many other minor differences in characteristics between caput units. Choose the 1 that entreaties to you most. Switch able light is nice if you desire the caput unit's show to fit the other instrumentality in your car. Ray M. Dolby Noise decrease and full logic tape controls are nice as well. Finally, a distant control can be utile or can be a waste material depending on whether you utilize it. A distant control mounted in the guidance wheel can be very convenient though. Some cadmium caputs come up with a buffer to minimise personal effects from bumps. This tin be utile but in my experience if you mount the caput unit of measurement securely it will not jump much anyway and using the anti-skip buffer can have got a flimsy negative consequence on sound quality because of the manner the buffer is implemented.

Labels: , , , , ,


Post a Comment

<< Home